| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | QSFP-40G-CSR4 | |
| 2 | Alcatel-Lucent | QSFP-4X10G-SR | |
| 3 | Arista | QSFP-40G-XSR4 | |
| 4 | Dell Force10 | 0MV31 | |
| 5 | H3C | QSFP-40G-CSR4-MM850 | |
| 6 | HPE Aruba | JH233A | |
| 7 | HPE H3C | JG709A | |
| 8 | Huawei | QSFP-40G-eSR4 | |
| 9 | Juniper | QFX-QSFP-40G-ESR4 | |
| 10 | NVIDIA(Mellanox) | MC2210411-SR4E |
| NVIDIA(Mellanox) Compatible | MC2210411-SR4E | Vendor Name | HYTOPTODEVICE |
| Form Factor | QSFP+ | Max Data Rate | 42Gbps (4x 10.5Gbps) |
| Wavelength | 850nm | Max Distance | 300m@OM4/400m@OM3 |
| Connector | MTP/MPO | Transmitter Type | VCSEL 850nm |
| Cable Type | MMF | Receiver Type | PIN |
| TX Power | -8.0~2.0dBm | Receiver Sensitivity | < -13dBm |
| Power Consumption | ≤1.5W | Modulation | NRZ |
| Protocols | 40G Ethernet, SATA/SAS3, IEEE 802.3ba, MSA Compliant | Operation Temperature | 0 to 70°C (32 to 158°F) |
Usage Guidelines & Best Practices
Fiber Choice: Only compatible with OM3 / OM4 multi‑mode MPO‑12 trunk cabling; single‑mode fiber cannot facilitate 850 nm SR4 operation and will produce link failure.
Distance Limit: Max 300m (OM3) / 400m (OM4). Dirty end faces, excessive splicing and sharp bending will reduce actual transmission distance.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Installation Specification: Hot‑plug supported; keep MPO connector end‑faces clean, observe minimum fiber‑bend radius requirements.
Operating Environment: Designed for commercial‑grade 0°C‑70°C ambient conditions; maintain adequate cabinet‑level airflow to prevent excessive module temperature build‑up.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
Pre-calibrated Mellanox dedicated EEPROM enables plug-and-play recognition and avoids port rejection and link instability. All stocked modules pass real machine burn-in and temperature cycling tests for mainstream Mellanox data center switches.
Validated Platforms:
Primary Application Scenarios





1. 40G Connectivity for Data Center
High speed, low overhead. The QSFP+ 40G transceiver brings gigabit-class throughput to dense data center racks while drawing less power and taking up less space.



FAQ
Q1: Can buyers deploy this 40GBASE-SR4E optic on a 100G QSFP28 Mellanox switch port with speed downgrade?
A: Often yes, if the port can be configured down to 40G speed. Support varies by platform, so verify the port's speed capability with your switch vendor before purchasing.
Q2: Is interconnection available between HYTOPTODEVICE optics and original Mellanox OEM transceivers on the same fiber link?
A: In most cases yes — SR4 links are standardized, so any two 40GBASE-SR4-compliant modules interoperate regardless of brand, as long as both ends use multimode fiber and the correct cable.
Q3: Does my Mellanox switch require firmware updates to identify this compatible 40GBASE-SR4E transceiver?
A: Many switches recognize standards-compliant modules without upgrades. Some OEM platforms need a minor firmware update or feature license to accept non-OEM optics — check your switch release notes.
Q4: What maximum fiber reach can purchasers expect from this Mellanox MC2210411-SR4E replacement module?
A: Per IEEE standard, 40GBASE-SR4E reaches 300 m on OM3 fiber and 400 m on OM4 multimode fiber. Longer runs require LR4/ER4 single-mode modules.
Q5: What wavelength and lane structure does this 4x10G breakout optical transceiver use?
A: 850 nm (VCSEL), operating as 4 independent 10G lanes in parallel for a total of 40 Gbps.
Q6: What power draw should customers expect for bulk ordered 40GBASE-SR4E transceivers during operation?
A: Typically around 1.0–1.5 W per module, depending on vendor and temperature — far lower than the MSA maximum, so it is safe for dense switch line cards.
Q7: Can network integrators hot swap this Mellanox compatible in-stock transceiver without powering off switches?
A: Yes, QSFP+ modules are hot-pluggable; you can install or replace them without powering down the switch, following normal ESD precautions.
Q8: What risks come with unclean MPO connectors for 40GBASE-SR4E multimode links in your data center project?
A: Critical. Dust or contamination on MPO ferrules is the #1 cause of link failures and can permanently damage VCSELs. Use an MPO inspection scope and cleaning tools before every insertion.
Q9: Is it acceptable to combine OM3 and OM4 fiber segments within one single 40GBASE-SR4E link for on-site project installation?
A: Yes, but the reach is limited by the shorter-grade segment (OM3), so a mixed link is rated at 100 m maximum.
Q10: What warranty and RMA service can resellers and project clients get for bulk orders?
A: We offer 5 years warranty with a simple RMA process: report the issue, return the module, and receive a replacement or credit. Confirm the policy in writing.
Q11: How will HYTOPTODEVICE handle DOA defective units for spot stock and wholesale bulk purchases?
A: HYTOPTODEVICE replaces DOA units free of charge within 30 days. Keep the packaging and test evidence for a fast RMA.
Q12: What is the proper installation workflow for Mellanox 40GBASE-SR4E transceivers during field deployment?
A: Align the module with the port keyway, insert gently until seated, and latch it. Do not force it; misaligned insertion can bend pins and damage both module and port.
Q13: What steps should I take to troubleshoot a downed fiber link right after module installation?
A: Check in order: module seating and latching, MPO cleanliness and polarity, fiber type (OM3/OM4), link partner speed, and DOM readings (TX power should be present; RX power within sensitivity range).
Q14: Can project buyers and resellers obtain datasheets and professional technical support from HYTOPTODEVICE?
A: Yes — datasheets, compatibility lists, quick-install guides, and test reports are provided, plus pre- and post-sale technical support by email or chat to help with deployment issues.
Q15: Are there import, export or certification limitations when ordering bulk quantities of these 40G optical modules?
A: 40G SR4 modules are widely available internationally and typically not subject to strict export licensing, but confirm import duties, RoHS requirements, and any local telecom certifications for your destination before ordering.
Packaging & Custom OEM Solutions
Every 40G QSFP+ SR4 module ships in sealed ESD-safe packaging, ready for same-day dispatch. Bulk orders offer OEM customization—logo printing and private labeling—tailored for network distributors, integrators, and enterprise deployments.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



