| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | QSFP-40G-CSR4 | |
| 2 | Alcatel-Lucent | QSFP-4X10G-SR | |
| 3 | Arista | QSFP-40G-XSR4 | |
| 4 | Dell Force10 | 0MV31 | |
| 5 | H3C | QSFP-40G-CSR4-MM850 | |
| 6 | HPE Aruba | JH233A | |
| 7 | HPE H3C | JG709A | |
| 8 | Huawei | QSFP-40G-eSR4 | |
| 9 | Juniper | QFX-QSFP-40G-ESR4 | |
| 10 | NVIDIA(Mellanox) | MC2210411-SR4E |
| Juniper Compatible | QFX-QSFP-40G-ESR4 | Vendor Name | HYTOPTODEVICE |
| Form Factor | QSFP+ | Max Data Rate | 42Gbps (4x 10.5Gbps) |
| Wavelength | 850nm | Max Distance | 300m@OM4/400m@OM3 |
| Connector | MTP/MPO | Transmitter Type | VCSEL 850nm |
| Cable Type | MMF | Receiver Type | PIN |
| TX Power | -8.0~2.0dBm | Receiver Sensitivity | < -13dBm |
| Power Consumption | ≤1.5W | Modulation | NRZ |
| Protocols | 40G Ethernet, SATA/SAS3, IEEE 802.3ba, MSA Compliant | Operation Temperature | 0 to 70°C (32 to 158°F) |
Usage Guidelines & Best Practices
Fiber Choice: Only compatible with OM3 / OM4 multi‑mode MPO‑12 trunk cabling; single‑mode fiber cannot facilitate 850 nm SR4 operation and will produce link failure.
Distance Limit: Max 300m (OM3) / 400m (OM4). Dirty end faces, excessive splicing and sharp bending will reduce actual transmission distance.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Installation Specification: Hot‑plug supported; keep MPO connector end‑faces clean, observe minimum fiber‑bend radius requirements.
Operating Environment: Designed for commercial‑grade 0°C‑70°C ambient conditions; maintain adequate cabinet‑level airflow to prevent excessive module temperature build‑up.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
Pre-calibrated Juniper Junos OS dedicated EEPROM ensures plug-and-play recognition, avoiding unrecognized port and link instability. All modules pass real-machine aging testing for mainstream Juniper QFX platforms.
Validated Juniper Platforms:
Primary Application Scenarios





1. 40G Connectivity for Data Center
High speed, low overhead. The QSFP+ 40G transceiver brings gigabit-class throughput to dense data center racks while drawing less power and taking up less space.



FAQ
Q1: Can a 40G SR4 optical transceiver run inside a QSFP28 100G switch port? A: Often yes, if the port can be configured down to 40G speed. Support varies by platform, so verify the port's speed capability with your switch vendor before purchasing.
Q2: Can I pair HYTOPTODEVICE third-party optics with OEM brand transceivers on opposite ends of the same fiber link? A: In most cases yes — SR4 links are standardized, so any two 40GBASE-SR4-compliant modules interoperate regardless of brand, as long as both ends use multimode fiber and the correct cable.
Q3: Is a switch firmware update mandatory to recognize this compatible 40G SR4 transceiver? A: Many switches recognize standards-compliant modules without upgrades. Some OEM platforms need a minor firmware update or feature license to accept non-OEM optics — check your switch release notes.
Q4: What is the maximum fiber transmission range for this 40G eSR4 transceiver? A: Per IEEE standard, 40GBASE-eSR4 reaches 300 m on OM3 fiber and 400 m on OM4 multimode fiber. Longer runs require LR4/ER4 single-mode modules.
Q5: What optical wavelength does HYTOPTODEVICE 40G SR4 QSFP+ module adopt for data transmission? A: 850 nm (VCSEL), operating as 4 independent 10G lanes in parallel for a total of 40 Gbps.
Q6: What is the typical power consumption of this 40G SR4 QSFP+ transceiver? A: Typically around 1.0–1.5 W per module, depending on vendor and temperature — far lower than the MSA maximum, so it is safe for dense switch line cards.
Q7: Can I hot swap this QSFP+ 40G SR4 module without powering off my network switch? A: Yes, QSFP+ modules are hot-pluggable; you can install or replace them without powering down the switch, following normal ESD precautions.
Q8: Why is MPO connector cleaning so important for 40G SR4 multimode fiber links? A: Critical. Dust or contamination on MPO ferrules is the #1 cause of link failures and can permanently damage VCSELs. Use an MPO inspection scope and cleaning tools before every insertion.
Q9: Can I combine OM3 and OM4 multimode fiber segments within one single 40G SR4 link? A: Yes, but the reach is limited by the shorter-grade segment (OM3), so a mixed link is rated at 100 m maximum.
Q10: What warranty and RMA process does HYTOPTODEVICE provide for bulk orders of 40G SR4 transceivers? A: We offer 5 years warranty with a simple RMA process: report the issue, return the module, and receive a replacement or credit. Confirm the policy in writing.
Q11: What support will I get when my purchased 40G SR4 module arrives DOA dead on arrival? A: HYTOPTODEVICE replaces DOA units free of charge within 30 days. Keep the packaging and test evidence for a fast RMA.
Q12: What is the correct installation method for HYTOPTODEVICE QSFP+ 40G SR4 transceiver? A: Align the module with the port keyway, insert gently until seated, and latch it. Do not force it; misaligned insertion can bend pins and damage both module and port.
Q13: How to troubleshoot when the 40G SR4 fiber link fails right after module installation? A: Check in order: module seating and latching, MPO cleanliness and polarity, fiber type (OM3/OM4), link partner speed, and DOM readings (TX power should be present; RX power within sensitivity range).
Q14: Can buyers get technical documentation and after-sale support from HYTOPTODEVICE for 40G SR4 deployment? A: Yes — datasheets, compatibility lists, quick-install guides, and test reports are provided, plus pre- and post-sale technical support by email or chat to help with deployment issues.
Q15: Are there any export limitations when shipping HYTOPTODEVICE 40G SR4 modules to overseas countries? A: 40G SR4 modules are widely available internationally and typically not subject to strict export licensing, but confirm import duties, RoHS requirements, and any local telecom certifications for your destination before ordering.
Packaging & Custom OEM Solutions
Every 40G QSFP+ SR4 module ships in sealed ESD-safe packaging, ready for same-day dispatch. Bulk orders offer OEM customization—logo printing and private labeling—tailored for network distributors, integrators, and enterprise deployments.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



