Juniper EX-SFP-10GE-DAC-50CM Compatible SFP+ to SFP+ DAC Cable 50cm | 10GBASE-CU Passive Copper Twinax Cable HYTOPTODEVICE
Product Overview
HYTOPTODEVICE EX-SFP-10GE-DAC-50CM compatible SFP+ passive twinax DAC cable is a direct replacement for original Juniper 0.5m 10G direct attach copper cable. It meets SFF-8431 and 10GBASE-CU MSA standards. This SFP+ passive DAC delivers stable, low-latency 10Gbps transmission for short intra-rack stacking and server uplink.
It is preloaded with Juniper EEPROM signature for plug-and-play and avoids Junos OS transceiver alerts. HYTOPTODEVICE supplies bulk stock, sample testing and OEM private label for Juniper data center projects.
Key Technical Specifications
| Juniper Compatible |
|
Vendor Name |
HYTOPTODEVICE |
| Connector |
SFP+ to SFP+ |
Max Data Rate |
10Gbps |
| Cable Length |
0.5m (1.6ft) |
Wire AWG |
AWG 30 |
| Cable Type |
Passive Twinax |
Power Consumption |
≤0.1W |
| Media |
Copper |
Operation Temperature |
0~ 70 °C (32 to 158°F) |
| Jacket Material |
PVC(OFNR) |
Protocols |
1x InfiniBand QDR, DDR, SDR, 10G Ethernet, Fibre Channel |
| Minimum Bend Radius |
20mm |
Application |
10G Ethernet |
For detailed technical specifications, please refer to the Datasheet
Usage Guidelines & Best Practices
-
Mandatory Port Setting: Host SFP+ port must enable 10GBASE-CU mode; link negotiation failure will happen if forced to optical mode.
-
Cabling Requirements: Do not exceed the minimum 23mm bend radius, avoid sharp folding, heavy extrusion or long-term tension on the cable assembly.
-
Port Installation Standard: Works only with standard SFP+ 10G ports; cannot be inserted into SFP or XFP slots. Disable the host’s third-party transceiver lock policy in advance if required.
-
Maintenance Specification: Hot‑swap supported, grip the pull tab instead of pulling the cable body during plug/unplug to prevent internal conductor damage.
- Testing & Storage: Run sample validation on target Cisco hardware before large bulk deployment; store spare cables in dry, dust‑free and anti‑static packaging.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List & Supported Devices
1. Validated HPE Hardware & Firmware
This SFP+ passive dac cable is preloaded with Juniper EEPROM data, supports alarm-free plug-and-play under Junos OS. Every cable passes target switch testing before shipment:
• Juniper EX2300 / EX3400, QFX5100 / QFX5120 switch platforms
• Juniper MX240 / MX480, SRX series service gateways
2. Multi-Brand Cross Interoperability
Built on universal MSA open standards, this SFP+ DAC cable can interoperate with mainstream network brands including Arista, H3C, Juniper, Dell, NVIDIA Mellanox and Fortinet, for mixed-vendor rack stacking and server fabric expansion.
3. Free Value-Added Services
-
Custom firmware for multi-device compatibility
-
Support sample testing before bulk orders for project pre-verification
-
Private-label customization and professional deployment guidanc
-
Strict batch consistency quality control
- Free custom EEPROM programming for special and legacy network environments
- Free EEPROM rewriting (Tools Included) with 24/7 Tech Support
Primary Application Scenarios
• Juniper EX/QFX switch intra-rack stacking links
• ToR switch to server low-latency 10G uplink
• Virtualization cluster and storage fabric interconnection
• Cost-effective short 10G links replacing fiber patch cords
• Bulk inventory sourcing for data center contractors and distributors
Connectivity Solutions(Applications)
1. 10G to 10G Direct Link for Switch-Switch
2. 10G to 10G Direct Link for Switch-NIC
3. Leaf-spine Architecture

The Core Feature
1. Cost-Effective Ultra-Short Connectivity
Using twinax copper, the SFP+ 10G DAC replaces a fiber pair and two optical transceivers, significantly cutting interconnect cost for short-reach links — plug-and-play, no modules required.

2. Ultra-Low Power, Maximum Energy Efficiency
The passive SFP+ 10G DAC draws near-zero power, reducing heat and energy costs in dense racks, while delivering a cost-effective, low-latency 10G link for short-reach connections — within a rack or across adjacent racks.

3.Host-Device Tested for Proven Interoperability
Every SFP+ passive twinax copper cable is rigorously tested for compatibility in the target switch environment, so you can deploy with confidence — no surprises, no downtime. Not sure it fits?
Compatibility Video available upon request.
4. 100% Individually Tested for Peak Performance
Every single unit is tested individually — no sampling, no shortcuts — to ensure optical compliance and continuous operational stability. Curious how we do it? Take a virtual tour of our
Test Center.

FAQ
Q1: Will this 10G SFP+ DAC cable work with my Cisco/HPE/Dell/Arista switch?
A: Yes, it works with multi-vendor 10GBASE-CU SFP+ ports. HYTOPTODEVICE pre-codes EEPROM and validates on target hardware. Test samples first for locked switch firmware.
Q2: Can I reflash/reprogram the EEPROM chip if I switch network vendors later?
A: Yes, EEPROM reprogramming is supported. HYTOPTODEVICE provides optional coding tools and free technical support for signature rewriting.
Q3: What is wire gauge (AWG) and how does it affect 10G DAC performance?
A: AWG shows copper thickness. Thin 30AWG is flexible for short runs. Thick 24AWG reduces signal loss for longer DAC links. This 50cm Juniper DAC uses 30AWG.
Q4: What is the minimum bend radius for a 10G SFP+ copper twinax cable?
A: The minimum bend radius is 23mm. Sharp bends damage internal wires and trigger intermittent CRC errors.
Q5: Does an active DAC cable consume significantly more power than a passive DAC?
A: Yes. Active DAC uses power for signal amplification. Our passive 10G DAC consumes less than 0.1W. It suits high-density low-power racks.
Q6: Why should I pick Passive DAC over Active Optical Cables (AOC) for short links?
A: Passive DAC has lower latency and lower cost for links under 7m. HYTOPTODEVICE passive twinax DAC has no optical chip power draw for intra-rack connections.
Q7: DAC vs. 10GBASE-T (RJ45 Cat6a): Which option generates less heat?
A: Passive DAC runs cooler. 10GBASE-T PHY chips create extra heat. Our passive copper DAC has no powered parts and produces minimal heat.
Q8: Can a 10G DAC cable cause electromagnetic interference (EMI) in high-density racks?
A: Properly shielded twinax DAC has low EMI risk. HYTOPTODEVICE full-shield design meets EMI standards for dense server racks.
Q9: Why am I getting packet loss, CRC errors, or link-flapping on my DAC connection?
A: It usually comes from sharp bends, damaged wires, dirty contacts or wrong port speed settings. HYTOPTODEVICE tests all DACs before shipment to filter defects.
Q10: Do DAC cables require Forward Error Correction (FEC) turned on?
A: No. Passive 10GBASE-CU DAC does not need FEC. FEC is mainly for optical links. Disable FEC for stable twinax DAC links.
Q11: Can DAC cables degrade or fail over time due to thermal stress?
A: Yes. Continuous high heat speeds up jacket aging and wire fatigue. HYTOPTODEVICE DACs pass temperature cycle testing for stable 24/7 operation.
Q12: What is the difference between PVC and LSZH (Low Smoke Zero Halogen) jacketing?
A: PVC is low-cost for general rack use. LSZH releases little smoke and no halogen gas in fire. HYTOPTODEVICE offers both jacket types for bulk orders.
Q13: Can repeated insertion/removal damage the SFP+ port cage or cable contacts?
A: Frequent plugging wears gold contacts slowly. HYTOPTODEVICE DAC uses high-quality gold-plated contacts to extend plug life.
Q14: Can I plug a 10G SFP+ DAC cable into a 25G SFP28 port?
A: It may negotiate down to 10G. Compatibility depends on switch firmware. Sample testing is strongly recommended.
Q15: Will a 10G DAC cable work in a 40G QSFP+ port using a breakout converter?
A: It depends on adapter and switch firmware. 10G SFP+ DAC cannot run native 40G. Check compatibility with HYTOPTODEVICE technical team first.
Packaging & Custom OEM Solutions
-
ESD Protection & Fast Shipping: Every transceiver is sealed in an ESD-safe bag and ready for same-day dispatch from stock.
-
Custom OEM & Branding: We provide logo printing, private labeling, and custom packaging to help distributors and integrators build their brand—no factory investment required.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
- Up to 70% cost savings vs OEM, transparent pricing & flexible bulk rates, supported quality returns
- 100% real-device compatible with Cisco, Huawei,Dell,Juniper, and Arista
- ISO 9001:2015 Shenzhen factory, full lineup: 1.25G/10G/25G/40G/100G/200G/400G/800G/1.6T transceivers
- Ample stock, fast global DHL/FedEx shipping in 3–5 working days
- Free pre-sales engineering support for custom EEPROM & private label firmware
- Real switch test videos available for pre-purchase review; inspection & shipping videos provided per order
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
-
ISO 9001: Certified quality management and production consistency.
-
CE & FCC: Fully compliant for seamless Global Market Access.
-
RoHS: Committed to environmental responsibility and hazardous material control.
-
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.

Rigorous Industrial Product Testing

100% 3rd Party Compatible

Partial Test Demonstration

