Extreme 10GB-BX40-D Compatible BiDi SFP+ 10G Transceiver 10GBASE-BX40-D (SMF, 1330nm-TX/1270nm-RX, 40km, Simplex LC, DDM)
Product Overview
Our HYTOPTODEVICE Extreme 10GB-BX40-D Compatible BiDi SFP+ 10G Transceiver is a long-range 10GBASE-BX40 uplink transceiver, built for 40km point-to-point transmission over single strand OS2 single mode fiber.
• Wavelength: Tx1330nm/Rx1270nm (Match Extreme 10GB-BX40-U standard BiDi pairing)
• Interface: Standard LC simplex connector
• Transmission Distance: Stable 40km @10Gbps SMF OS2
Compliant with Hot-Pluggable SFP+ MSA, SFF-8472,SFP-8431, IEEE 802.3ae and RoHS standards and fully DDM/DOM support, Delivering high-speed performance with optimized power efficiency, this DDM supported BiDi SFP+ 10G Transceive is the ideal solution for cross-campus backbones, metropolitan area network (MAN) rings, and long-range data center interconnects (DCI). We support samples, bulk wholesale and OEM private labeling, submit bulk inquiry or RFQ for competitive pricing and long-term supply contracts.
Key Technical Specifications
Our BiDi SFP+ 10G Transceive is factory-calibrated and fully tested for optical stability, low bit error rate and consistent interoperability. Adopting high-quality DFB laser and PIN receiver chips, it supports real-time DDM monitoring and safe hot-swappable operation. Below full parameter table matches Extreme 10GB-BX40-D industrial BiDi standard, zero compatibility risks after switch firmware upgrades.
| Extreme compatible |
10GB-BX40-D |
Vendor Name |
HYTOPTODEVICE |
| Form Factor |
SFP+ |
Max Data Rate |
10.7Gbps |
| Wavelength |
TX1330nm/RX1270nm |
Max Distance |
40km |
| Connector |
Simplex LC |
Transmitter Type |
1330nm DFB |
| Cable Type |
SMF |
Receiver Type |
PIN |
| TX Power |
-1.0~+5dBm |
Receiver Sensitivity |
< -15dBm |
| Max. Power Consumption |
≤1W |
DOM/DDM |
Fully Supported |
| Protocols |
SFP+ MSA, SFF-8472, IEEE 802.3ae, RoHS Compliant |
Operation Temperature |
0 to 70°C (32 to 158°F) |
Pairing Guidance
Single-strand BiDi transmission relies on reverse wavelength matching to realize two-way data communication, and this BiDi SFP+ 10G Transceiver strictly follows Extreme official pairing specifications. The HYTOPTODEVICE Extreme 10GB-BX40-D module (Tx1330nm/Rx1270nm) must be paired with 10GB-BX40-U (Tx1270nm/Rx1330nm) to build a valid 40km 10G fiber link. Installing two identical 10GB-BX40-D modules on both ends will directly cause link failure. To avoid on-site deployment errors, HYTOPTODEVICE provides pre-tested and fully matched module pairs for all bulk orders of this BiDi SFP+ 10G Transceiver, ensuring one-step successful networking.
The Required Matched Pairs here: 10G SFP+ BiDi Tx 1270nm / Rx 1330nm 40km module
Full Compatibility List & Supported Network Hardware
1.Extreme Native Compatibility
This HYTOPTODEVICE BiDi SFP+ 10G Transceiver requires no manual CLI configuration or firmware upgrade, achieving zero-configuration online operation on mainstream Extreme Networks hardware. Verified compatible Extreme device models are listed line by line below:
1. Extreme X440 Series Access Switches
X440-G2-24t-10GE4, X440-G2-48t-10GE4, X440-G2-24p-10GE4
2. Extreme X460 Series Aggregation Switches
X460-G2-24p-10GE4, X460-G2-48p-10GE4
3. Extreme X670 / X870 Series Data Center Core Switches
X670-G2-48x-4q, X870-48x-8c high-density 10G core switching chassis
4. Extreme VSP Series Virtual Service Platform Routers
VSP 4900, VSP 8400 enterprise multi-service core routers with standard SFP+ expansion slots
2.Multi-Brand Cross Compatibility
Built to universal SFP+ MSA standards, HYTOPTODEVICE’s Extreme-compatible BiDi SFP+ 10G 40KM Transceiver unlocks OEM vendor lock-in for hybrid multi-vendor metro networks.
- Open-Brand (Plug-and-Play): Fortinet, Ubiquiti, MikroTik, D-Link, Zyxel and other open switches
- Locked-Brand (Custom Coding): Cisco, H3C, Huawei, Dell, Juniper, Ruijie, fully compatible with latest Ciena OS firmware
3.Free Custom EEPROM Re-Flash Service
Complimentary permanent EEPROM rewrite for all bulk orders of SFP+ 10G BiDi 40KM Transceiver. Upgrade Extreme system or migrate modules to other brand racks; our team re-codes firmware free of charge to maintain stable 40km single-fiber bidirectional links for evolving multi-vendor metro architectures.
Primary Application Scenarios
Versatile commercial BiDi SFP+ 10G Transceiver optimized for cost-saving single-fiber long-range 10G networking for enterprise, park and ISP service scenarios.
1. Extreme switch long-distance 10G uplink deployment, saving fiber core resources with single-strand BiDi SFP+ 10G Transceiver
2. Cross-building enterprise campus 40km 10G interconnection using high-stability BiDi SFP+ 10G Transceiver
3. Outdoor cabinet long-range 10G signal transmission for commercial parks with reliable BiDi SFP+ 10G Transceiver
4. ISP last-mile broadband access and remote base station 10G networking with economical BiDi SFP+ 10G Transceiver
5. Enterprise 10G structured cabling optimization, cutting project costs via single-fiber BiDi SFP+ 10G Transceiver deployment
Connectivity Solutions(Applications)
1.Switch-to-Switch 10G BiDi Single Fiber Uplink
Deploy paired BiDi transceivers between core and aggregation switches for single-fiber 10G uplinks, saving fiber resources for campus expansion and datacenter stacking projects.
2.Switch-to-10G SFP+ NIC Server Long Distance Link
Create single-fiber high-speed links between core switches and server NICs, eliminating gigabit bandwidth bottlenecks for cloud storage and high-performance workstations.

3.Enterprise 10G Single Fiber Structured Cabling System Layout
Perfectly matched with OS2 simplex single-mode structured cabling, realizing end-to-end 10G transmission across access, aggregation and core layers for office parks and commercial buildings.

Features | Maximized Fiber Utilization
Cut Fiber Costs by 50% with High-Density 10G BiDi 40km SFP+ Optics
This Extreme BiDi SFP+ 10G Transceiver achieves bidirectional 10G transmission via a single fiber strand. Replacing traditional dual-fiber cabling layouts, it significantly boosts existing fiber utilization, saves 50% physical fiber resources, and delivers cost-efficient stable 40km long-reach links for layered Extreme metro core-to-access network construction. Compact SFP+ form factor, low power consumption and hot-swappable design simplify field deployment and lower long-term cabinet OPEX.

FAQ
Q1: How can I organize port records for BiDi transceivers within dense patch panels without messy asset files?
A: Conventional dual-fiber cable filing templates cannot match single-port alternating transmit and receive wavelength layout of BiDi hardware, which brings heavy labeling workload for cabinet management. HYTOPTODEVICE clearly marked BiDi SFP+ 10G Transceiver simplifies port registration for high-density structured cabling deployment.
Q2: What triggers random packet loss on BiDi links that maintained stable transmission in the previous year?
A: Long-term fiber displacement, aging and micro-bending will steadily raise signal attenuation. 40km BiDi optics adopt compact optical power budget with almost no spare capacity to offset gradual fiber performance degradation. HYTOPTODEVICE power-margin enhanced BiDi SFP+ 10G Transceiver adapts to long-running fiber infrastructure aging scenarios.
Q3: Why do continuous bit errors appear while real-time optical power values stay within normal thresholds on 40km BiDi links?
A: Long-distance single-mode transmission builds up chromatic dispersion across 1270nm and 1330nm wavebands, distorting 10G signal waveforms invisibly. Reliable luminous intensity cannot counteract waveform distortion to eliminate BER faults. HYTOPTODEVICE dispersion optimized BiDi SFP+ 10G Transceiver stabilizes signal quality for long-span backbone transmission.
Q4: Will minor dirt on bulkhead adapters trigger full service outage of 40km single-fiber BiDi connections?
A: Tiny dust residue on fiber end faces creates two-way interference on single-strand BiDi links. Besides weakening light intensity, contaminants reflect local transmitting signals back into the built-in receiver and disable normal signal demodulation. HYTOPTODEVICE anti-reflection port BiDi SFP+ 10G Transceiver lowers outage risks caused by uncleaned fiber interfaces.
Q5: Which factor leads to frequent crosstalk faults inside Extreme switch cabinets loaded with BiDi modules?
A: Budget generic BiDi transceivers equip diplexer components with insufficient isolation performance. Internal laser transmitting signals leak into nearby receiving circuits and generate persistent chassis crosstalk alarms. HYTOPTODEVICE high-isolation diplexer BiDi SFP+ 10G Transceiver erases internal signal leakage for full-density switch port installation.
Q6: Why do data center cooling expenses surge after upgrading long-distance links to 40km BiDi transceivers?
A: 40km long-reach BiDi modules adopt high-output laser chips that generate extra heat during continuous operation. Mass deployment raises overall thermal load and pushes HVAC cooling systems to run at higher power consumption. HYTOPTODEVICE low thermal emission BiDi SFP+ 10G Transceiver cuts overall heat burden to reduce data center cooling costs.
Q7: Why cannot ordinary single-mode loopback jumpers complete functional verification for BiDi SFP+ ports?
A: BiDi hardware separates transmit and receive traffic onto two independent wavelengths. Standard loopback lines short-circuit local TX and RX ports directly, failing to match the dual-wavelength working logic of BiDi modules. HYTOPTODEVICE dual-wavelength separated BiDi SFP+ 10G Transceiver needs dedicated testing tools for accurate port performance inspection.
Q8: Why does DDM real-time optical monitoring fail to display data after Extreme switch firmware upgrades?
A: OS version updates adjust the system’s register reading mechanism for pluggable transceivers. Most third-party BiDi optics use non-standard register layouts, leading to incomplete or garbled diagnostic telemetry after firmware iterations. HYTOPTODEVICE full register compatible BiDi SFP+ 10G Transceiver retains complete DDM functions across all official switch OS versions.
Q9: Why do field maintenance crews need to carry two sets of spare BiDi hardware for on-site repair work?
A: Single-fiber BiDi links require matched TX1270 and TX1330 module pairs to achieve bidirectional communication. Carrying only one wavelength variant cannot resolve unexpected transceiver breakdowns on site. HYTOPTODEVICE pre-paired BiDi SFP+ 10G Transceiver sets standardize spare inventory management for field service teams.
Q10: What causes repeated delays during on-site commissioning of 40km BiDi fiber links?
A: Field engineers rely on habitual use of duplex dual-fiber jumpers for traditional network construction, while BiDi single-fiber links require dedicated simplex patch cords. Wrong cable selection leads to repeated debugging and postponed project delivery timelines. HYTOPTODEVICE usage-labeled BiDi SFP+ 10G Transceiver reduces wiring errors to speed up network turn-up progress.
Q11: Why do dark fiber operators charge extra rental fees for networks built with BiDi single-fiber transceivers?
A: BiDi modules occupy fixed exclusive wavelength pairs on each fiber core, limiting operators’ ability to multiplex multiple clients’ independent services over the same fiber strand. Reduced fiber resource utilization pushes carriers to set higher leasing prices for BiDi single-fiber circuits. HYTOPTODEVICE cost-efficient BiDi SFP+ 10G Transceiver helps enterprises cut long-term dark fiber rental expenditure.
Q12: Is it possible to deploy breakout cables to split a single 10G BiDi fiber link into multiple low-speed independent channels?
A: BiDi single-fiber transmission only supports one bidirectional 10G channel without native multiplex breakout capacity. Optical splitters or breakout cables will exhaust the tight power budget and terminate normal link operation. HYTOPTODEVICE single-channel fixed BiDi SFP+ 10G Transceiver is designed for point-to-point 10G single-fiber transmission only.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
- Up to 70% cost savings vs OEM, transparent pricing & flexible bulk rates, supported quality returns
- 100% real-device compatible with Cisco, Huawei,Dell,Juniper, and Arista
- ISO 9001:2015 Shenzhen factory, full lineup: 1.25G/10G/25G/40G/100G/200G/400G/800G/1.6T transceivers
- Ample stock, fast global DHL/FedEx shipping in 3–5 working days
- Free pre-sales engineering support for custom EEPROM & private label firmware
- Real switch test videos available for pre-purchase review; inspection & shipping videos provided per order
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
-
ISO 9001: Certified quality management and production consistency.
-
CE & FCC: Fully compliant for seamless Global Market Access.
-
RoHS: Committed to environmental responsibility and hazardous material control.
-
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.

Rigorous Industrial Product Testing

100% 3rd Party Compatible

Partial Test Demonstration

Others


