Dell Force10 CBL-10GSFP-DAC-0.5M Compatible SFP+ to SFP+ DAC Cable 50cm | 10GBASE-CU Passive Copper Twinax Cable HYTOPTODEVICE
Product Overview
HYTOPTODEVICE CBL-10GSFP-DAC-0.5M compatible SFP+ passive twinax DAC cable is a direct replacement for original Dell Force10 0.5m 10G copper DAC cable. It meets SFF-8431 and 10GBASE-CU MSA standards. This SFP+ passive DAC delivers stable, low-latency 10Gbps transmission for short intra-rack Force10 switch stacking and server uplink.
It is preloaded with Dell Force10 EEPROM signature for plug-and-play and avoids FTOS transceiver alerts. HYTOPTODEVICE supplies bulk stock, sample testing and OEM private label for Dell Force10 data center projects.
Key Technical Specifications
| Dell Force10 Compatible |
|
Vendor Name |
HYTOPTODEVICE |
| Connector |
SFP+ to SFP+ |
Max Data Rate |
10Gbps |
| Cable Length |
0.5m (1.6ft) |
Wire AWG |
AWG 30 |
| Cable Type |
Passive Twinax |
Power Consumption |
≤0.1W |
| Media |
Copper |
Operation Temperature |
0~ 70 °C (32 to 158°F) |
| Jacket Material |
PVC(OFNR) |
Protocols |
1x InfiniBand QDR, DDR, SDR, 10G Ethernet, Fibre Channel |
| Minimum Bend Radius |
20mm |
Application |
10G Ethernet |
For detailed technical specifications, please refer to the Datasheet
Usage Guidelines & Best Practices
-
Mandatory Port Setting: Host SFP+ port must enable 10GBASE-CU mode; link negotiation failure will happen if forced to optical mode.
-
Cabling Requirements: Do not exceed the minimum 23mm bend radius, avoid sharp folding, heavy extrusion or long-term tension on the cable assembly.
-
Port Installation Standard: Works only with standard SFP+ 10G ports; cannot be inserted into SFP or XFP slots. Disable the host’s third-party transceiver lock policy in advance if required.
-
Maintenance Specification: Hot‑swap supported, grip the pull tab instead of pulling the cable body during plug/unplug to prevent internal conductor damage.
- Testing & Storage: Run sample validation on target Cisco hardware before large bulk deployment; store spare cables in dry, dust‑free and anti‑static packaging.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List & Supported Devices
1. Validated HPE Hardware & Firmware
This SFP+ passive dac cable is preloaded with Dell Force10 EEPROM data, supports alarm-free plug-and-play under FTOS. Every cable passes target switch testing before shipment:
• Dell Force10 S4810, S5000, S6010-ON switch platforms
• Dell Force10 MXL blade switch, Z9000 core switch
2. Multi-Brand Cross Interoperability
Built on universal MSA open standards, this SFP+ DAC cable can interoperate with mainstream network brands including Arista, H3C, Juniper, Dell, NVIDIA Mellanox and Fortinet, for mixed-vendor rack stacking and server fabric expansion.
3. Free Value-Added Services
-
Custom firmware for multi-device compatibility
-
Support sample testing before bulk orders for project pre-verification
-
Private-label customization and professional deployment guidanc
-
Strict batch consistency quality control
- Free custom EEPROM programming for special and legacy network environments
- Free EEPROM rewriting (Tools Included) with 24/7 Tech Support
Primary Application Scenarios
• Dell Force10 FTOS switch intra-rack stacking links
• ToR switch to server low-latency 10G uplink
• Virtualization cluster and storage fabric interconnection
• Cost-effective short 10G links replacing fiber patch cords
• Bulk inventory sourcing for data center contractors and distributors
Connectivity Solutions(Applications)
1. 10G to 10G Direct Link for Switch-Switch
2. 10G to 10G Direct Link for Switch-NIC
3. Leaf-spine Architecture

The Core Feature
1. Cost-Effective Ultra-Short Connectivity
Using twinax copper, the SFP+ 10G DAC replaces a fiber pair and two optical transceivers, significantly cutting interconnect cost for short-reach links — plug-and-play, no modules required.

2. Ultra-Low Power, Maximum Energy Efficiency
The passive SFP+ 10G DAC draws near-zero power, reducing heat and energy costs in dense racks, while delivering a cost-effective, low-latency 10G link for short-reach connections — within a rack or across adjacent racks.

3.Host-Device Tested for Proven Interoperability
Every SFP+ passive twinax copper cable is rigorously tested for compatibility in the target switch environment, so you can deploy with confidence — no surprises, no downtime. Not sure it fits?
Compatibility Video available upon request.
4. 100% Individually Tested for Peak Performance
Every single unit is tested individually — no sampling, no shortcuts — to ensure optical compliance and continuous operational stability. Curious how we do it? Take a virtual tour of our
Test Center.

FAQ
Q1: Will this Dell Force10 twinax DAC run smoothly on other vendor 10G SFP+ switch ports?
A: Yes, it supports cross-vendor 10GBASE-CU SFP+ ports. HYTOPTODEVICE pre-codes EEPROM and validates on target hardware. Test samples first for locked switch firmware.
Q2: Can I rewrite the EEPROM ID if I migrate from Force10 switches to another brand later?
A: Yes, EEPROM reprogramming is supported. HYTOPTODEVICE provides optional coding tools and free lifetime technical support for signature modification.
Q3: How does conductor AWG size impact signal quality on short 10G Force10 stacking DAC?
A: AWG stands for copper conductor thickness. This 50cm Force10 DAC uses 30AWG. Thin gauge brings great flexibility for tight rack routing, thicker 24AWG cuts attenuation for longer DAC runs.
Q4: What bending specification must I follow for this 10G Force10 twinax DAC?
A: Follow the 20mm minimum bend radius. The standard minimum bend radius is typically 5 times the outer cable diameter. Bending lower than this can deform the internal twinax structure and cause bit errors.
Q5: Is there obvious power consumption difference between passive twinax DAC and signal-boost active DAC?
A: Yes, active DAC consumes extra power for signal amplification. Our passive 10G DAC draws less than 0.1W. It helps reduce power draw for high-density Force10 switch stacks.
Q6: Why select passive twinax DAC instead of AOC for short Force10 stacking connections?
A: Passive DAC delivers better latency and lower cost for links under 7 meters. HYTOPTODEVICE twinax DAC has no optical chips, perfect for fixed short-distance FTOS switch stacking.
Q7: Between 10G twinax DAC and Cat6a 10GBASE-T copper, which produces less rack heat?
A: Passive DAC runs much cooler. 10GBASE-T PHY chips continuously generate heat. This DAC has no powered components and lowers thermal load in dense Force10 racks.
Q8: Will this twinax DAC create EMI interference when deployed inside packed Force10 blade racks?
A: Our fully shielded twinax design keeps EMI low. HYTOPTODEVICE DAC meets industry EMC standards. The shielding blocks crosstalk among closely packed network blades.
Q9: What common factors trigger unstable DAC links, packet drops and rising CRC counters on FTOS?
A: Damaged conductors or dirty contacts are the top triggers. Our factory 100% inspection filters defective units. Sharp bends and mismatched port speed also lead to link flapping.
Q10: Is FEC feature required to maintain stable 10GBASE-CU DAC links on Dell Force10?
A: FEC is not required for passive 10GBASE-CU DAC. FEC is built for long-reach optical links. Disable FEC to skip extra processing overhead on Force10 stacking ports.
Q11: Can long-time high cabinet temperature shorten the usable lifespan of twinax DAC cables?
A: Yes, sustained high heat speeds up jacket and copper aging. HYTOPTODEVICE DACs pass thermal cycle testing. It supports reliable 24/7 operation inside warm data center cabinets.
Q12: What practical differences separate PVC and LSZH cable jackets for Force10 data center deployments?
A: PVC fits regular indoor racks at lower procurement cost. LSZH releases minimal smoke and zero halogens in fire. HYTOPTODEVICE offers both jacket choices for bulk Force10 DAC orders.
Q13: Will frequent plug and unplug wear the SFP+ contacts or port cages on Dell Force10 switches?
A: Repeated hot-plugging slowly wears gold plating on contacts. HYTOPTODEVICE DAC uses premium gold-plated contacts. It extends plug cycles for regular Force10 fabric reconfiguration.
Q14: Can I insert this 10G SFP+ DAC into a 25G SFP28 uplink port on modern switches?
A: It may negotiate down to 10G speed. Final performance depends on switch firmware. Complete sample verification before large-scale SFP28 uplink deployment.
Q15: Can I use this 10G DAC together with breakout adapters on a 40G QSFP+ port?
A: Native 40G operation is not supported. This DAC only transmits 10G signal. Confirm breakout adapter and switch compatibility with the HYTOPTODEVICE technical team in advance.
Packaging & Custom OEM Solutions
-
ESD Protection & Fast Shipping: Every transceiver is sealed in an ESD-safe bag and ready for same-day dispatch from stock.
-
Custom OEM & Branding: We provide logo printing, private labeling, and custom packaging to help distributors and integrators build their brand—no factory investment required.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
- Up to 70% cost savings vs OEM, transparent pricing & flexible bulk rates, supported quality returns
- 100% real-device compatible with Cisco, Huawei,Dell,Juniper, and Arista
- ISO 9001:2015 Shenzhen factory, full lineup: 1.25G/10G/25G/40G/100G/200G/400G/800G/1.6T transceivers
- Ample stock, fast global DHL/FedEx shipping in 3–5 working days
- Free pre-sales engineering support for custom EEPROM & private label firmware
- Real switch test videos available for pre-purchase review; inspection & shipping videos provided per order
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
-
ISO 9001: Certified quality management and production consistency.
-
CE & FCC: Fully compliant for seamless Global Market Access.
-
RoHS: Committed to environmental responsibility and hazardous material control.
-
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.

Rigorous Industrial Product Testing

100% 3rd Party Compatible

Partial Test Demonstration

