| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | QSFP-H40G-CU50CM | |
| 2 | Arista Networks | CAB-Q-Q-0.5M | |
| 3 | Juniper | EX-QSFP-40GE-DAC-50CM | |
| 4 | Brocade | 40G-QSFP-C-00501 | |
| 5 | Dell | 332-1362 | |
| 6 | Intel | XLDACBL05 | |
| 7 | NVIDIA/Mellanox | MC2206130-00A |
| Brocade Compatible |
40G-QSFP-C-00501
|
Vendor Name | HYTOPTODEVICE |
| Connector | QSFP+ to QSFP+ | Max Data Rate | 40Gbps |
| Cable Length | 0.5m (1.6ft) | Wire AWG | AWG 30 |
| Cable Type | Passive Twinax | Power Consumption | ≤0.5W |
| Media | Copper | Operation Temperature | 0~ 70 °C (32 to 158°F) |
| Jacket Material | PVC(OFNR) | Protocols | SFF-8436, QSFP+ MSA and IEEE 802.3ba |
| Minimum Bend Radius | 35mm | Application | 40G InfiniBand 8x DDR, 4x QDR, 10/40 Gigabit Ethernet, Fibre Channel |
Usage Guidelines & Best Practices
Mandatory Port Setting: Host QSFP+ port must enable 40GBASE-CR4 mode; link negotiation failure will happen if forced to optical mode.
Cabling Requirements: Do not exceed the minimum 35mm bend radius, avoid sharp folding, heavy extrusion or long-term tension on the cable assembly.
Port Installation Standard: Works only with standard QSFP+ 40G ports; cannot be inserted into SFP+ or XFP slots. Disable the host’s third-party transceiver lock policy in advance if required.
Maintenance Specification: Hot‑swap supported, grip the pull tab instead of pulling the cable body during plug/unplug to prevent internal conductor damage.
Operating Environment: This commercial-grade cable operates reliably within 0℃‑70℃; avoid installation beside high-heat power modules.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List & Supported Devices
Built on universal MSA open standards, this 40G QSFP+ passive copper cable can interoperate with mainstream network brands including Arista, H3C, Juniper, Dell, NVIDIA Mellanox and Fortinet, for mixed-vendor rack stacking and server fabric expansion.





Q1: Can this Brocade compatible 40G QSFP+ twinax DAC connect between Brocade and other brand network hardware? A: Yes, this HYTOPTODEVICE 40G QSFP+ passive copper cable supports cross-brand interworking. It comes pre-flashed with Brocade Fabric OS optimized EEPROM and fully tested to deliver reliable 40GBASE Ethernet links across multi-vendor environments.
Q2: Why will Fabric OS raise a transceiver mismatch alert once I plug in this DAC? A: This warning triggers when the switch’s vendor lock check fails. HYTOPTODEVICE pre-programs Brocade-specific EEPROM profile for this 40G QSFP+ passive copper cable to minimize transceiver alert issues in your 40GBASE Ethernet deployment.
Q3: Are MSA-standardized 40G twinax DACs guaranteed to run plug-and-play on white-box open network switches? A: No, MSA specifications only define mechanical and electrical parameters. Generic twinax cables often lack valid identification signatures, while HYTOPTODEVICE 40G QSFP+ passive copper cable passes real open-switch validation for stable 40GBASE Ethernet operation.
Q4: What connection layout is suitable for QSFP+ to 4×SFP+ breakout twinax DAC? A: A breakout DAC splits one 40G QSFP+ port into four separate 10G SFP+ links. This straight HYTOPTODEVICE 40G QSFP+ passive copper cable transmits full 40G bandwidth natively for point-to-point Brocade 40GBASE Ethernet links.
Q5: Do Brocade SLX and VDX switches require special port configuration to activate breakout DAC links? A: Yes, breakout mode must be enabled through Fabric OS CLI on supported ports. This HYTOPTODEVICE straight 40G QSFP+ passive copper cable needs no breakout configuration and runs native 40GBASE Ethernet out of the box.
Q6: Which data center deployments fit straight 40G DAC versus breakout 40G DAC? A: Straight 40G DAC creates one full 40G connection between two QSFP+ ports; breakout DAC divides bandwidth for 10G downlinks. Our 40G QSFP+ passive copper cable is built for native Brocade 40GBASE Ethernet point-to-point interconnection.
Q7: What is the maximum reliable reach you can get with passive 40G QSFP+ twinax copper? A: The reliable upper limit for passive 40G QSFP+ twinax is 5–7 meters. This 0.5m HYTOPTODEVICE 40G QSFP+ passive copper cable is ideal for ultra-short rack internal 40GBASE Ethernet with minimal signal attenuation.
Q8: How do different AWG ratings change signal loss for 40G twinax DAC on Brocade racks? A: Thicker wires (lower AWG numbers like 24AWG) experience lower signal attenuation over longer runs (5m–7m), whereas thinner wires (30AWG) are better suited for short, flexible runs (0.5m–2m). This 30AWG HYTOPTODEVICE 40G QSFP+ passive copper cable balances flexible routing and steady signal integrity for short 40GBASE Ethernet links.
Q9: Which AWG grade works best for dense cable management with 40G QSFP+ DAC assemblies? A: Yes. 24AWG cables are thick, heavy, and rigid. They require careful bend radius management to prevent putting excessive mechanical strain on switch port cages. 30AWG twinax offers superior flexibility for dense layouts. This HYTOPTODEVICE 0.5-2m 40G QSFP+ passive copper cable uses 30AWG, making routing easier on high-density Brocade patch panels and cable arms for 40GBASE Ethernet.
Q10: Is it acceptable to route passive 40G QSFP+ DAC outside the server rack or run it through building walls? A: No, passive twinax DAC is designed exclusively for indoor cabinet deployment. It has no outdoor-rated jacket protection, so this 40G QSFP+ passive copper cable must stay inside data racks for 40GBASE Ethernet.
Q11: What replacement option should I select when the required link length exceeds 7 meters? A: Active Optical Cable (AOC) is the proper upgrade for links longer than 7m. This HYTOPTODEVICE 40G QSFP+ passive copper cable provides a zero-power, cost-effective solution for short rack-local 40GBASE Ethernet connections.
Q12: How does the overall infrastructure cost compare between 40G twinax DAC and QSFP+ transceivers paired with MTP fiber? A: Passive twinax DAC greatly cuts total hardware cost by removing optical module expenses. This HYTOPTODEVICE 40G QSFP+ passive copper cable reduces investment for short Brocade 40GBASE Ethernet fabric interconnections.
Q13: Will adjacent power distribution cables introduce EMI interference to this 40G QSFP+ passive copper DAC? A: Shielded twinax suppresses EMI but remains more sensitive than fiber media. HYTOPTODEVICE uses premium shielding on this 40G QSFP+ passive copper cable to sustain stable 40GBASE Ethernet performance beside power cabling in Brocade racks.
Q14: Can a simple adapter allow a 40G QSFP+ DAC to operate inside a regular 10G SFP+ port? A: No, QSFP+ and SFP+ have different pin assignments and lane grouping structures. This 40G QSFP+ passive copper cable only functions between two native QSFP+ ports to establish valid 40GBASE Ethernet.
Q15: Can this Brocade compatible 40G QSFP+ DAC directly connect a server QSFP+ NIC to my Brocade switch? A: Yes, this works if the server NIC features a native QSFP+ interface. This HYTOPTODEVICE 40G QSFP+ passive copper cable builds low-latency 40GBASE Ethernet links between 40G NICs and Brocade switching hardware.
Packaging & Custom OEM Solutions
ESD Protection & Fast Shipping: Every transceiver is sealed in an ESD-safe bag and ready for same-day dispatch from stock.
Custom OEM & Branding: We provide logo printing, private labeling, and custom packaging to help distributors and integrators build their brand—no factory investment required.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.




