| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | QSFP-40G-CSR4 | |
| 2 | Alcatel-Lucent | QSFP-4X10G-SR | |
| 3 | Arista | QSFP-40G-XSR4 | |
| 4 | Dell | 0MV31 | |
| 5 | H3C | QSFP-40G-CSR4-MM850 | |
| 6 | HPE Aruba | JH233A | |
| 7 | HPE H3C | JG709A | |
| 8 | Huawei | QSFP-40G-eSR4 | |
| 9 | Juniper | QFX-QSFP-40G-ESR4 | |
| 10 | NVIDIA(Mellanox) | MC2210411-SR4E |
| Alcatel-Lucent Compatible | QSFP-4X10G-SR | Vendor Name | HYTOPTODEVICE |
| Form Factor | QSFP+ | Max Data Rate | 42Gbps (4x 10.5Gbps) |
| Wavelength | 850nm | Max Distance | 300m@OM4/400m@OM3 |
| Connector | MTP/MPO | Transmitter Type | VCSEL 850nm |
| Cable Type | MMF | Receiver Type | PIN |
| TX Power | -8.0~2.0dBm | Receiver Sensitivity | < -13dBm |
| Power Consumption | ≤1.5W | Modulation | NRZ |
| Protocols | 40G Ethernet, SATA/SAS3, IEEE 802.3ba, MSA Compliant | Operation Temperature | 0 to 70°C (32 to 158°F) |
Usage Guidelines & Best Practices
Fiber Choice: Only compatible with OM3 / OM4 multi‑mode MPO‑12 trunk cabling; single‑mode fiber cannot facilitate 850 nm SR4 operation and will produce link failure.
Distance Limit: 100‑metre maximum operating reach on OM3, 150‑metre maximum on OM4; excessive splice joints, dirty connector end‑faces or sharp fiber bends degrade practical transmission distances.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Installation Specification: Hot‑plug supported; keep MPO connector end‑faces clean, observe minimum fiber‑bend radius requirements.
Operating Environment: Designed for commercial‑grade 0°C‑70°C ambient conditions; maintain adequate cabinet‑level airflow to prevent excessive module temperature build‑up.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
Primary Application Scenarios





1. 40G Connectivity for Data Center
High speed, low overhead. The QSFP+ 40G transceiver brings gigabit-class throughput to dense data center racks while drawing less power and taking up less space.



FAQ
Q1: What makes this Alcatel-Lucent compatible QSFP+ 40G SR4 module different from standard 150m SR4 optics?
A: This transceiver uses 4x10GBASE-SR specification to achieve extended reach up to 400m over OM4 multimode fiber, while standard SR4 modules only support 150m. It is built for longer cross-rack data center links where ordinary QSFP+ 40G SR4 products fall short.
Q2: How do I activate the 4x10G breakout function of this QSFP+ 40G SR4 module on Alcatel-Lucent switches?
A: You can enable breakout mode via Alcatel-Lucent OS CLI commands after stable module insertion. Once activated, the single QSFP+ 40G port will split into four independent 10G SFP+ ports. HYTOPTODEVICE supplies configuration guidance to help you complete setup without link errors.
Q3: Will this third-party QSFP+ 40G SR4 breakout optic trigger unsupported transceiver alerts on Alcatel-Lucent hardware?
A: It will not trigger warnings. HYTOPTODEVICE preloads Alcatel-Lucent matched EEPROM and completes real machine validation for every module. It bypasses vendor lock-in, supports DDM readout and hot swap, solving the common QSFP+ 40G SR4 unsupported transceiver error.
Q4: Can this 400m long-range QSFP+ 40G SR4 module maintain stable traffic for production data center links?
A: Yes, it delivers stable transmission. The module complies with IEEE 4x10GBASE-SR standards and passes 72-hour full rate burn-in testing. It maintains low bit error rate and zero packet loss within the rated distance, suitable for production trunk and enterprise core traffic.
Q5: Can I interconnect this breakout QSFP+ 40G SR4 module with regular SR4 transceivers on the opposite fiber end?
A: Mixed interconnection is not recommended. Both ends of the fiber link should use matched 4x10GBASE-SR modules for full performance. Pairing with standard SR4 optics will limit maximum distance and disable breakout functionality.
Q6: Which multimode fiber grade delivers the full 400m reach for this QSFP+ 40G SR4 breakout module?
A: OM4 multimode fiber is recommended to reach the full 400m distance. OM3 supports up to 300m. Lower-grade OM2 fiber is not suitable, as insufficient bandwidth and higher optical loss will cause QSFP+ 40G SR4 link instability.
Q7: Does this QSFP+ 40G SR4 module support DDM real-time optical monitoring on Alcatel-Lucent switches?
A: Full DDM monitoring is supported. It follows SFF-8436 DOM standard and reports real-time optical power, temperature and voltage on Alcatel-Lucent management interfaces, simplifying QSFP+ 40G SR4 link health checks and troubleshooting.
Q8: Can I hot swap this QSFP+ 40G SR4 transceiver while Alcatel-Lucent switches remain online?
A: Hot swap is supported. The module follows QSFP+ MSA hot-plug design with built-in ESD protection. You can replace modules online without powering down the switch or disrupting live business traffic for routine maintenance.
Q9: What support can HYTOPTODEVICE provide if I encounter QSFP+ 40G SR4 link flapping or packet loss issues?
A: HYTOPTODEVICE provides end-to-end troubleshooting support including pre-shipment optical calibration, free EEPROM reprogramming, fiber cleaning guidance and port configuration advice. Bulk orders get batch consistency testing to reduce QSFP+ 40G SR4 link failure risk.
Q10: What warranty and technical support are available for bulk wholesale orders of this QSFP+ 40G SR4 module?
A: We offer a 5-year official warranty and standardized RMA service for all bulk QSFP+ 40G SR4 purchases. Our technical team provides 24/7 remote help for breakout configuration, compatibility debugging and link troubleshooting to support large-scale project rollout.
Packaging & Custom OEM Solutions
Every 40G QSFP+ SR4 module ships in sealed ESD-safe packaging, ready for same-day dispatch. Bulk orders offer OEM customization—logo printing and private labeling—tailored for network distributors, integrators, and enterprise deployments.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



