| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | GLC-BX80-UA | |
| 2 | Cisco | Cisco GLC-BX80-UA-I | |
| 3 | Brocade | E1MG-1G-BXU-80 | |
| 4 | Dell | SFP-GE-BX80-1490 | |
| 5 | Extreme | MGBIC-BX80-U | |
| 6 | H3C | SFP-GE-LH70-SM1490-BIDI | |
| 7 | HPE H3C | SFP-1G-BXU-80 | |
| 8 | Huawei | SFP-GE-ZBXD1 | |
| 9 | Juniper | SFP-GE80KT14R15 | |
| 10 | MikroTik | S-4554LC80D-1490 | |
| 11 | Netgear | SFP-GE-BX80 |
| H3C Compatible | SFP-GE-LH70-SM1490-BIDI | Vendor Name | HYTOPTODEVICE |
| Form Factor | SFP | Max Data Rate | 1.25Gbps |
| Wavelength | TX1490nm/RX1550nm | Max Distance | 80km |
| Connector | Simplex LC | Transmitter Type | 1490nm DFB |
| Cable Type | SMF | Receiver Type | PIN |
| TX Power | 0~5dBm | Receiver Sensitivity | < -26.0dBm |
| Protocols | SFF-8472 MSA Compliant, IEEE 802.3ah-2004 | Operation Temperature | 0 to 70°C (32 to 158°F) |
Complementary Pairing: BiDi transceivers must be deployed in matched pairs (e.g., TX1490/RX1550 with TX1550/RX1490). Mismatched wavelengths cannot establish a link.
Fiber Choice: Use Single-Mode Fiber (SMF) only. Do NOT use MMF.
Connector Match: Simplex LC (UPC/PC polish only). Do NOT use Duplex LC or APC.
Laser Safety: Class 1 Laser. Never look directly into optical ports or fiber end-faces.
ESD Safety: Wear an anti-static wrist strap before handling the transceiver.
Cleanliness & Dust: Keep dust caps installed on all unused ports. Clean fiber connectors with an optical cleaning pen before insertion; dust causes over 80% of link failures.
Optical Attenuator Required: For short-distance testing or links (<20 km), connect a 10dB–15dB attenuator to the RX port to prevent receiver damage.
Installation & Hot-Swap: MSA compliant. Insert and remove gently without powering down the device.
High Loss / Packet Drops: Ensure fiber bend radius exceeds 30 mm, inspect optical power levels, and clean connectors.
No Link: Verify complementary BIDI wavelength pairing requirement; clean Simplex LC end-faces; check port speed configuration.
1. Supported Hardware & Firmware








Q1: Apart from H3C Comware‑based switches, can this H3C‑profile BiDi SFP module operate normally on other brand network devices? A1: It can run across multi‑brand platforms after dedicated firmware modification. Factory‑loaded H3C‑specific EEPROM enables hassle‑free deployment for H3C S‑series core and access switches; custom EEPROM rewriting is required for Cisco, Arista, Juniper or Dell hardware. Execute sample validation ahead of large‑volume wholesale procurement to avoid transceiver‑recognition malfunctions.
Q2: Is it permissible to insert this 1.25G BiDi SFP module into a port originally engineered for 10G SFP+ transceivers? A2: Some 10G‑rate SFP+ ports deliver backward compatibility for gigabit SFP optics, yet manual port‑speed locking to 1G must be completed inside switch configuration. Physical insertion fit will not guarantee auto‑negotiation success; manual configuration adjustment is essential for steady gigabit link status.
Q3: Can I combine this Tx1490/Rx1550 BiDi SFP module with conventional dual‑fiber gigabit SFP hardware to build functional network links? A3: Such mixing cannot generate usable network connectivity. This BiDi SFP module applies WDM multiplexing over one fiber strand, whereas ordinary dual‑fiber SFP transmits signals across two separate physical fiber cores. Always match it with reverse‑wavelength complementary BiDi partner modules instead of mixing dual‑fiber optics.
Q4: What network fault symptoms will emerge if BiDi SFP modules with identical wavelength setting are deployed on both sides of fiber span? A4: You will encounter complete link shutdown together with LOS alarms reported by connected network switches. Both sides transmit light at 1490 nm and receive at 1550 nm without wavelength cross‑matching. One side must adopt Tx1490/Rx1550 and the remote‑end must use Tx1550/Rx1490 to finish bidirectional WDM transmission path.
Q5: During on‑site commissioning work, how can field technicians quickly differentiate Tx1490 and Tx1550 BiDi SFP module units? A5: Check printed marking information on SFP metal housing shell. Every BiDi SFP module carries explicit Tx‑Rx wavelength labelling. Never judge merely according to plastic latch color; double‑check printed label content before cabling work to prevent wavelength‑mismatch accidents.
Q6: Which fiber‑cable variant shall field engineers prepare for deploying this H3C‑compatible long‑reach BiDi SFP module? A6: Simplex‑LC terminated OS1 / OS2 single‑mode patch cords are mandatory. Duplex‑LC and multimode fiber cables prove incompatible for 80 km single‑strand BiDi transmission scenarios. Thoroughly clean simplex‑LC connector faces before plug‑in to cut insertion‑loss values and reduce random LOS fault risks for long‑distance enterprise links.
Q7: What optical chip composition is integrated within this 80‑km‑reach H3C‑compatible BiDi SFP module? A7: This BiDi SFP module integrates DFB laser transmitter paired with PIN receiver hardware. PIN receiver delivers receiving sensitivity reaching down to ‑26 dBm. This mature chipset provides consistent signal performance under real‑world 80 km single‑mode fiber enterprise deployment scenarios.
Q8: What real‑world link‑budget performance can network planners anticipate with this 80 km BiDi SFP module on practical enterprise fiber infrastructure? A8: This module offers TX output power 0‑5 dBm and RX sensitivity better than ‑26 dBm, delivering minimum 26 dB overall link budget. Standard single‑mode fiber brings roughly 0.25 dB/km attenuation within 1490‑1550 nm spectral band. Reserve extra loss allowance for field splices and connector joints; keep cumulative total loss under 26 dB for reliable full‑distance operation.
Q9: Will this long‑haul 80 km BiDi SFP module consume substantially more power than short‑range 10‑20 km BiDi SFP module alternatives? A9: Power consumption remains strictly controlled below 1 W. It adopts proven DFB laser plus PIN‑receiver chip architecture. It fully complies with SFP MSA power‑draw specifications and brings no overload risk for standard SFP host switch ports.
Q10: For enterprise park network‑upgrade initiatives, what tangible business value can single‑fiber BiDi SFP module bring compared to traditional dual‑fiber gigabit SFP hardware? A10: BiDi SFP module halves fiber‑core consumption for sites facing fiber‑pair constraints. WDM technology supports bidirectional gigabit traffic over one fiber strand. It fits cross‑park inter‑building links, multi‑site branch backhaul and network‑renovation jobs where laying new fiber pairs incurs heavy capital expenditure.
Q11: Can this BiDi SFP module be inserted and operated inside existing CWDM or DWDM wavelength‑multiplexing network setup? A11: Deployment inside standard CWDM / DWDM systems is strongly discouraged. Its fixed 1490 nm /1550 nm operating wavelengths overlap commonly‑used CWDM channel spectrum ranges. Select purpose‑built CWDM‑rated optical transceivers if wavelength‑multiplexed networking forms part of your enterprise project scope.
Q12: What factory‑backed warranty coverage can buyers obtain for bulk & wholesale orders of this H3C‑compatible BiDi SFP module? A12: HYTOPTODEVICE supplies standard 5‑year factory warranty covering manufacturing‑originated hardware defects. Warranty validity applies for hardware failures appearing within rated 0‑70 °C commercial operating environment; damage triggered by ESD surge, polluted fiber‑connector faces, optical‑receiver overload and improper field‑handling procedures falls outside warranty coverage scope.
Q13: Why does 80km‑class BiDi SFP module carry higher unit price versus shorter‑distance 10km or 20km BiDi SFP module products? A13: High‑power DFB/EML laser components, high‑sensitivity PIN receivers, and precise wavelength‑isolation filters push up manufacturing costs. Short‑distance BiDi transceivers can implement lower‑cost optical‑component schemes. Additional fine‑tuned optical calibration and long‑haul‑oriented burn‑in aging steps further increase total production expenses.
Q14: What troubleshooting workflow shall network technicians follow when meeting Rx Power Low or LOS alarms triggered by this BiDi SFP module on H3C Comware switches? A14: Initiate fault‑isolation work from physical‑layer field connections. Clean simplex‑LC patch‑cable connector surfaces, reseat BiDi SFP module firmly inside SFP slots, double‑check wavelength‑pairing correctness and test end‑to‑end total optical link loss. If measured loss exceeds module‑specified link budget, shorten transmission span or deploy appropriate fiber amplifier hardware for extra‑long single‑fiber links.
Q15: Which typical root factors produce unstable intermittent link‑flapping on enterprise single‑fiber BiDi SFP module connections running Comware OS? A15: Link‑flapping is mostly triggered by physical‑layer faults associated with PIN‑receiver performance. Common triggers include contaminated fiber‑connector faces, insufficient received optical margin, reversed wavelength pairing, ESD‑damaged PIN‑receiver hardware or excessive cabinet internal temperature. Fetch DDM real‑time optical‑power and temperature readouts to speed‑up fault‑source identification work.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



