| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Alcatel-Lucent | SFP-10G-SR | |
| 2 | Cisco Meraki | MA-SFP-10GB-SR | |
| 3 | D-Link | DEM-431XT | |
| 4 | Dell | GP-10GSFP-1S | |
| 5 | Juniper | SRX-SFP-10GE-SR | |
| 6 | H3C | SFP-XG-SX-MM850-A | |
| 7 | IBM | 46C3447 | |
| 8 | EdgeCore | ET5402-SR |
|
Cisco MerakiCompatible |
MA-SFP-10GB-SR |
Vendor Name |
HYTOPTODEVICE |
| Form Factor | SFP+ | Max Data Rate | 10.7Gbps |
| Wavelength | 850nm | Max Distance | 300m on OM3 |
| Connector | Duplex LC | Transmitter Type | VCSEL 850nm |
| Cable Type | MMF | Receiver Type | PIN |
| TX Power | -6.5~-0.5dBm | Receiver Sensitivity | < -10.5dBm |
| Power Consumption | ≤1W | Operation Temperature | 0 to 70°C (32 to 158°F) |
Usage Guidelines & Best Practices
Fiber Choice: Duplex LC Multimode Fiber (MMF) — OM3 / OM4 (50/125 µm). Do NOT use SMF.
Connector Match: UPC/PC polish only. Do NOT use APC.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Link Setup:Set speed to 10Gbps Full Duplex. Lock speed manually if auto-negotiation fails.
Handling: Wear ESD protection. Keep fiber bend radius ≥ 30 mm.
Installation & Hot-Swap Rules: MSA hot-swappable. Insert/remove gently without powering down.
Environment: Commercial temperature (0°C to 70°C). Avoid extreme heat, moisture, and dust.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
Pre‑programmed Meraki EEPROM,real‑machine validated to skip transceiver validation alerts,no link flapping,no port lockdown for Meraki cloud‑managed infrastructure.
Validated platforms:
Main Application Scenarios









FAQ
Q1: Will this SFP‑10G‑SR module work with my specific switch brand (e.g., Cisco, Arista, Juniper, Dell)? A: Built to SFP+ MSA mechanical & electrical specs. Meraki‑flashed profile delivers alarm‑free operation on Meraki MX/MS hardware. For other brands,some vendors enforce transceiver lock; verify host firmware before bulk orders. Submit exact hardware model for pre‑sales compatibility check.
Q2: Will third‑party or generic SFP‑10G‑SR modules void my equipment warranty? A: Qualified third‑party transceivers do not automatically void network hardware warranty. Vendors may decline coverage if hardware damage is directly traced to faulty optics. Our units undergo comprehensive factory stress testing to minimize failure risk; retain test records for enterprise audit when purchasing large‑volume Meraki replacement optics.
Q3: Will this module work in Network Interface Cards (NICs) like Intel or Broadcom? A: Yes,compatible with most Intel X520/X710 and Broadcom NetXtreme SFP+ NIC adapters. Certain server NIC firmware blocks non‑OEM optics. Request generic‑profile variant and validate NIC firmware prior to large‑scale server NIC deployment.
Q4: How far can SFP‑10G‑SR reach using legacy OM1 or OM2 fiber? A: Older OM1/OM2 multimode cables lack sufficient modal bandwidth for full‑spec 10GBASE‑SR. OM1 reaches ~33m,OM2 ~82m only. These short distances seldom satisfy campus‑scale requirements. Deploy OM3 or OM4 multimode fiber for full‑rated transmission in bulk Meraki network builds.
Q5: What optical connector interface does the SFP‑10G‑SR use? A: This Meraki‑compatible SFP‑10G‑SR utilizes duplex LC‑UPC connectors,industry‑standard for 10G multimode enterprise links. Avoid APC angled‑end‑face patch cords; APC generates extra return loss and elevates bit‑error risk on UPC‑calibrated transceivers.
Q6: Can I break out a 40G QSFP+ SR4 port to four 10G SFP‑10G‑SR modules? A: Yes when paired with passive 40G‑to‑4×10G SR4 breakout cable. Each breakout lane connects to one independent SFP‑10G‑SR unit. Enable breakout mode inside switch CLI; misconfigured port settings produce total link loss in mixed‑speed Meraki fabrics.
Q7: What latency should I expect from an SFP‑10G‑SR connection? A: Transceiver‑originated latency sits 10‑30ns per module. End‑to‑end latency depends largely on switch ASIC and fiber propagation. Minimal overhead makes it suitable for Meraki virtualization and campus workloads; conduct real‑world validation for ultra‑low‑latency production environments.
Q8: How does heat output compare between SFP‑10G‑SR and 10G copper RJ45 optics? A: SFP‑10G‑SR draws ≤1.0W versus 2.5‑4W for typical 10GBASE‑T copper SFP+. Mass copper deployments raise cabinet PUE and cooling load. For high‑density Meraki switch racks,optical SFP‑10G‑SR reduces overall thermal pressure during large‑volume roll‑outs.
Q9: Does SFP‑10G‑SR support FEC (Forward Error Correction)? A: No on‑module hardware FEC,consistent with IEEE 10GBASE‑SR definition. If error correction is required,activate switch‑side ASIC‑level FEC. Maintain link loss within optical budget to keep BER ≤1×10⁻¹²; do not compensate poor fiber performance relying on missing transceiver FEC.
Q10: Does SFP‑10G‑SR support hot‑swapping? A: Yes,complies with SFP+ MSA hot‑plug specification. Insert/remove modules without power‑cycling Meraki appliances. Avoid frequent hot‑swap amid heavy production traffic; brief link interruption occurs during replacement. Schedule maintenance windows for mass module swap‑outs.
Q11: What is the average lifespan (MTBF) of an SFP‑10G‑SR module? A: Calculated MTBF exceeds 1,000,000 hours under 0‑70℃ clean cabinet operating conditions. Real‑world service life is impacted by temperature,vibration and repeated hot‑swap cycles. Maintain proper rack ventilation to maximize module lifetime for long‑term Meraki campus infrastructure.
Q12: Does the transceiver comply with MSA (Multi‑Source Agreement) standards? A: Fully compliant with SFP+ MSA and SFF‑8472 DDM monitoring specifications. Meraki‑specific EEPROM only modifies identification data; mechanical,electrical and monitoring functions remain strictly MSA‑aligned for third‑party replacement optics.
Q13: How do dust and dirt affect SFP‑10G‑SR performance? A: Contaminated LC‑UPC end‑faces are a leading source of unstable Meraki 10G links. Dust and fingerprints increase insertion loss,creating random packet loss and intermittent link flaps even with link‑up status showing. Implement regular optical connector cleaning as part of Meraki network maintenance routines.
Q14: Are all generic SFP‑10G‑SR optics built with the same internal components? A: No. Budget generic transceivers employ un‑screened laser chips and low‑grade components,raising BER risk and shortening service life. HYTOPTODEVICE uses grade‑A VCSEL‑PIN assemblies with multi‑stage aging,well‑suited for enterprise‑scale Meraki bulk procurement.
Q15: Is it safe to look directly into the optical port of an active SFP‑10G‑SR? A: No. Though classified Class1 laser,the invisible 850nm VCSEL infrared beam can damage eyes upon prolonged direct exposure. Never stare into powered‑on transceiver ports or unterminated fiber patch‑cords inside live Meraki network hardware.
Packaging & Custom OEM Solutions
Every 10G SFP+ module comes individually sealed in standard anti-static (ESD-safe) packaging, pre-stocked and ready for immediate shipment. For bulk orders, we offer custom OEM packaging—including logo printing and private labeling—tailored for network distributors, system integrators, and enterprise deployments.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



